Pinnacle Flashlights Blog

The Nitecore EZAA LED Flashlights are back in stock!

               
These are the latest models with improved runtimes on low. The NiteCore EZ Series flashlights are ultra-compact, simple flashlights that feature aggressive knurling for grip, two-stage activation for simplicity of use, and hard-anodized aircraft-grade aluminum for durability and strength. Runs on a single AA battery and puts out an amazing 130 lumens on high and 10 lumens on low. Check out the entire Nitecore Tactical line and the rest of our selection at PinnacleFlashlights.com!

PinnacleFlashlights.com is proud to announce even more new arrivals to our extensive line of cutting-edge, rugged, and powerful LED flashlights. JETBeam Tactical Flashlights! We are continuously adding models to the site, but please be sure to check out the newest tactical flashlights in the market: JETBeam M1X which features the MC-E LED putting out over 700 lumens and JETBeam RRT-1 Raptor featuring the XR-E R2 LED and variable output control.

     
See the complete line of JETBeam and many other Tactical LED flashlights at: www.PinnacleFlashlights.com

Tough. Versatile. Multi-functional. Easy to operate. Like the soldiers it’s made for, the Olight Tactical Line is a carefully honed weapon of war. The M20 and M30 features a rugged body, stainless steel striking bezel, blindingly bright strobe light, and multiple functions to give it strength and versatility never seen before in the hand-held lighting market. The M20 & M30 Warrior are all the lighting tool you need in the battlefield or on the job. Bright, rugged, and flexible, the multiple output levels and modes lend it a versatility and durability that make it the ideal tool for any task. The Olight Tactical Line is also a great choice for personal protection; the blinding light and crenellated striking bezel on both ends give added effectiveness when used for self-defense.

     
See the complete line of Olight and many other Tactical LED flashlights at: www.PinnacleFlashlights.com

We have added two new additions to the Pinnacle Flashlights Light Tunnel. The EagleTac M2 and the EagleTac T100C2. Below are two thumbnails at the 25ft range:

See the complete interactive beamshot comparison page including Fenix, Nitecore, and Surefire at:

The Pinnacle Flashlights Light Tunnel

In its stock form, the EagleTac M2/M2X uses the controller ring on the bezel to smoothly switch between the following modes: Off > Low > Med > High > Turbo > Strobe. Additionally, the stock tailcap can be swapped out for the M25 module to add a click switch to the either the M2 or M2X. With the click switch the user often does not require that the bezel have an “off” position. Also, some users do not need the strobe and accidentally trigger it while trying to switch the light to turbo output. This article will show you how to disable both the “off” and “strobe” features using commonly available items. The modification should take less than 5 minutes to complete!

Note: Pinnacle Flashlights is not responsible for personal injuries or damages caused to your EagleTac M2/M2X while attempting to perform this modification.

Step 1: You will need the following items:    - EagleTac M2/M2X    - Masking Tape    - Scissors    - Super Glue    - Paper Clip    - Old Hotel/Credit Card
Step 2: Orient the M2/M2X so that the tailcap is towards you and the bezel is facing away. Place a piece of the masking tape around the bezel right above the selector ring. The tailcap should be clicked “on” and the bezel rotated all the way to your “left” in the “off” position. Mark on the tape the position of the left edge of the large tab. Now, rotate the ring to the “right” until the light turns on “low”. Again, mark on the tape the position of the left edge of the tab. The tape will have 2 markings like the image to the right.
Step 3: Rotate the ring completely to the “right” so that it is in “strobe”. Mark on the tape the position of the left edge of the same tab used in Step 2. Rotate the ring to the “left” until the light switches to “turbo”. Again, mark on the tape the position of the left edge of the tab. Your tape should have 2 additional markings like the image to the right.
Step 4: At this point, the tape should have 4 markings. Note that they may or may not be equal.
Step 5: Remove the bezel. Remove the selector ring by gently pulling it over the threaded end of the bezel. Observe the slot in the bezel where the selector ring stops.
Step 6: Observe the slot in the bezel on the other side where the selector ring stops. Clean the grease off of both of these areas with a cotton swab or tissue.
Step 7: Cut a sliver of the credit card about the width of the notch in the bezel. Then cut 2 pieces which will be the lengths of the 2 measurements made on the tape.
Step 8: The 2 plastic pieces can be slightly bent to better fit the curvature of the bezel
Step 9: Test fit the pieces. Note that the piece for the “off to low” goes on the “left” side of the slot and the piece for the “strobe to turbo” goes on the right side. Place a small strip of super glue on the bezel and carefully place the plastic pieces in their appropriate locations. Press them down firmly with a paper clip and remove any excess glue.
Step 10: Give the glue sufficient time to set and dry. The finished product should look like the image to the right. Replace the selector ring and reattach the bezel to the body!

So how well does this modification work? Check out the video below!

See the entire line of the world’s toughest, brightest, and most advanced flashlights at www.PinnacleFlashlights.com